A számítógépes ventilátorok mindig 100% -on működnek, hacsak nem mondott másképpen?

Tartalomjegyzék:

A számítógépes ventilátorok mindig 100% -on működnek, hacsak nem mondott másképpen?
A számítógépes ventilátorok mindig 100% -on működnek, hacsak nem mondott másképpen?

Videó: A számítógépes ventilátorok mindig 100% -on működnek, hacsak nem mondott másképpen?

Videó: A számítógépes ventilátorok mindig 100% -on működnek, hacsak nem mondott másképpen?
Videó: Как отключить рекламу на ПК, ТВ и смартфоне – самый простой способ - YouTube 2024, Április
Anonim
Akár laptopokon, asztali gépeken, akár játékkonzolokon keresztül, mindannyian hallottuk a rendszer rajongói hangulatát a háttérben. Milyen pontosan tudják, hogy ezek a kis hűtőventilátorok mikor forgatják le, lefelé, és egyébként mérsékeljék a levegő mennyiségét?
Akár laptopokon, asztali gépeken, akár játékkonzolokon keresztül, mindannyian hallottuk a rendszer rajongói hangulatát a háttérben. Milyen pontosan tudják, hogy ezek a kis hűtőventilátorok mikor forgatják le, lefelé, és egyébként mérsékeljék a levegő mennyiségét?

A mai Kérdések és válaszok munkamenetét a Stack Exchange SuperUser, a szakma által vezetett Q & A webhelyek csoportosulása alapján kapjuk meg.

A kérdés

SuperUser olvasó darkAsPitch csodálkozik:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

Tehát hogyan működnek? Teljes hólyag, hacsak másként nem parancsolt?

A válasz

A SuperUser közreműködője, a Journeyman Geek az alábbi betekintést nyújtja:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

A társalgó Hyperslug kiemeli, hogy a kivételek hogyan játszanak:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

És ott van: a külső vezérlésen kívül valamilyen mechanizmus (legyen az alaplap bemenet, eset hőmérő vagy intelligens tápegység), a ventilátorok a legmagasabb fordulatszámon futnak, amit az áramforrás lehetővé tesz.

Van valami a magyarázathoz? Hangzik ki a megjegyzésekben. Szeretne többet válaszolni a többi technikus-tudós Stack Exchange felhasználóiról? Nézze meg a teljes vitafonalat itt.

Ajánlott: